Astrophotography Pixel Scale & Field of View Calculator

Image scale, sampling and framing for any telescope and camera

Astrophotography pixel scale & field of view

scale=206.265×pixel size (μm)F (mm) ′′/px\text{scale} = 206.265 \times \dfrac{\text{pixel size } (\mu\text{m})}{F \text{ (mm)}} \ {}^{\prime\prime}/\text{px}

mm
f/
3.1″ per pixel
Field of view 5.38° × 3.6° · Sensor 23.5 × 15.7 mm
Undersampled: 1 px across a 3″ star. Fewer than 2 pixels across a star: stars can look square and fine detail is lost. Fine for wide fields; drizzle integration in stacking software can recover some resolution. A longer focal length or smaller pixels would fix it, at the cost of field of view.
Frame
Andromeda Galaxy (M31), 190′ × 60′ · fits in the frame

The camera's field (the rectangle) and the target, to the same scale. Sizes are approximate visual extents.

Untracked tripod exposureLongest exposureNotes
NPF rule1.1 sPinpoint stars on modern sensors (stars at the celestial equator; closer to the pole allows longer)
500 rule1.3 sCrop factor 1.53; older rule, shows slight trailing on high-resolution sensors

Related: the Focal Length & Focal Ratio Calculator (for reducers and Barlows) and the True Field of View Calculator for the same framing question at the eyepiece.

Before buying a camera for a telescope, or a telescope for a camera, two questions decide whether the pair will work: how much sky does the sensor cover, and how much sky does each pixel cover? The first decides which targets fit. The second decides whether the camera can record the detail the sky allows.

Pixel scale

scale=206.265×pF\text{scale} = 206.265 \times \frac{p}{F}

pp is the pixel size in micrometres and FF the focal length in millimetres; the result is in arcseconds per pixel. 206,265 is the number of arcseconds in a radian, and the micrometre and millimetre units take care of the factor of 1,000. Binning 2×2 combines four pixels into one, which doubles the scale.

A RedCat 51 (250 mm) with a 3.76 µm camera gives about 3.1″ per pixel. The same camera on a C8 at 2032 mm gives 0.38″ per pixel, eight times finer.

Sampling: matching the camera to the sky

The atmosphere blurs every star into a small disc. Its width, the FWHM (full width at half maximum), is your seeing: about 2″ on a good night at a decent site, 3″ on an average one. The usual aim is 2 to 3 pixels across that disc.

Planetary imaging is the exception. With very short exposures that freeze the seeing (“lucky imaging”), planetary imagers deliberately sample much finer, usually at a focal ratio around 5 times the pixel size in µm.

Field of view

FOV=2arctan⁡(s2F)\text{FOV} = 2 \arctan\left(\frac{s}{2F}\right)

ss is the sensor’s width or height in millimetres. The framing preview draws the sensor and a target at the same scale, so you can see whether the whole Andromeda Galaxy fits (it needs about 3° × 1°) or whether the Ring Nebula is a speck.

Untracked exposures: the NPF and 500 rules

On a fixed tripod the sky turns during the exposure, and stars trail. The old 500 rule divides 500 by the focal length times the crop factor. It was worked out for film and allows visible trailing on today’s high-resolution sensors. The NPF rule, from Frédéric Michaud of the Société Astronomique de France, takes the f-number and pixel size into account:

t=35N+30pft = \frac{35N + 30p}{f}

Both give the worst case, for stars on the celestial equator. Stars near the celestial pole move less, so you can expose longer when pointing there.

The Telescope Focal Length & Focal Ratio Calculator shows what a reducer or Barlow does to your focal length, and the True Field of View Calculator answers the same framing question at the eyepiece.

View source on GitHub

Changelog

  • 2026-11-18Published.